Montrose Leather Works Small Leather Key Chain Process


I’ve thought about this for some time and I think I’m finally ready to give this out… My process in creating The Montrose Leather Works Small Leather Key Chain.

SmallKey4Blog01jpg

I’ve seen this replicated in the past. And it was shocking to me at first. Then I realized “Duh, it’s so easy to build”… although I did do some researching on how long and short to make it and where to get some really great hardware. So, if you haven’t already HERE IT IS.

First, you’ll need a few things:

Tools
Ruler (preferrably metal)
Awl
Hand Punch
Knife or blade

You’ll need at least one or the other of either the Awl or the Hand Punch. Sorry, kids. There’s just no other way… well, there probably is. But, having one or the other of these tools will make it easier. Using the Hand Punch will give you a little bit of a cleaner hole.

SmallKeysTools01jpg

Materials
Split RIng (1 inch)
5/8″ Square Trigger Snap
Leather

I purchased both of the hardware at a leather supply shop. I like using the 1″ Split Rings but you can substitute for whatever size you like (but probably nothing smaller than 1″). I usually have these in production all of the time so I purchase them in bulk.
I like the Square 5/8″ Trigger Snap. You may substitute for the rounded corners. But, I just prefer this look. IMPORTANT: If you go with a different size Trigger Snap, you will have to cut your leather at a different width.
I typically use this dark brown leather. But, you can substitute for any other leather you like (or any other material for that matter). But, I would stress that you use a weight at about no more than 5oz leather.
TAKE NOTE: I’ve indicated where holes should be punch with RED CIRCLES.

SmallKeysMaterials02jpg

Let’s get started…
Get your leather material, whatever it may be, and cut a 6″ long strip that is JUST A HAIR under 5/8″ wide. Once you’ve got that, create two marks for holes at 1/4 of an inch from one end. Now, make two more marks for holes 1/5 inch FROM THE TWO PREVIOUS MARKS. Try to get these holes somewhere near centered on the leather. It should look something like the following image.

SmallKeysHoles01jpg

Now that you’ve gotten one end done, do exactly the same on the other end. Once you’re done with that end you should have a total of 8 holes (4 on each end). These will be your stitching holes.
At this point you’ll want to get your hardware. Slip your piece of leather through both the Split Ring and the Trigger Snap. IMPORTANT: Make certain that the Trigger Snap is set on the SMOOTH side of the leather. Otherwise, once you start to stitch, your Trigger Snap will be laying on the inside of the keychain. And, that’s not where you want it.

SmallKeysNOStitch01jpg

Now you’ll want each of the end of your leather to meet. If you measured propperly, your stitching holes should line up perfectly as well. If you have a small clip handy, I would suggest using that to hold the ends in place. I makes stitching much easier.

SmallKeysEndsTogether01jpg

With everything lined up, bring the hardware DOWN so that they aren’t in your way when you start stitching. You’ll want to start with the holes CLOSEST TO THE EDGE of the leather first.

SmallKeysFirstStitch01jpg

Now, bring UP the Trigger Snap as far as possible. It should be close to the stitched threads but past the next set of stitching holes. And, leave the Split Ring down on the other end.

SmallKeysTriggerUP01jpg

Finally, stitch through the last set of stitching holes.

And, there you have it. You’ve just completed your own Montrse Leather Works Small Key Chain!

SmallKeySkyBlueBack

Other things you can do:
You could use rivets instead of stitching this piece together. However, I would suggest against this. It might not seem like it, but stitching is much stronger and will last longer than the rivets will hold this piece together. If used frequently, there will be a lot of stress and wear. And, rivets will just not stand up as well as good stitching work.
If you decide to go with veg tan leather, you can decorate it with some tooling. This may give it a little bit more of a decorative feel. Or maybe, if you can find small enough letter, monogram it with initials.
You can go with whatever color thread you want. I would, however, recommend something that’s very heavy duty. You don’t want to really go with anything light weight. If used frequently, the thread may wear or break quite easily.
It’s also possible to use other hardware. Brass is readily available. However, brass Split Rings are a little bit more difficult to come by and may be a little bit more expensive. You wouldn’t really want to mix-n-match brass with nickle.
There are probably a ton of other things that you can do. But, these are just a few suggestions. Go ahead and go nuts if you want.

Now, if for some reason you can’t get a hold of any of the tools or materials email us and we’ll see if we can put a kit together for you with hardware and pre-punched and pre-cut material for a small fee. All you’d need to do is stitch it up with a needle and thread yourself.

If you have any questions please don’t hesitate to contact me. I hope this was helpful and an enjoyable read on the process. Please leave a comment and share this post. Thanks and good luck!

www.MontroseLeatherWorks.com
www.instagram.com/MontroseLeatherWorks
www.etsy.com/shop/MontroseLeatherWorks

Advertisements

Leather Drawer Handle Pulls

A few weeks ago I took some time to do a little bit of DIYing. We had purchased these bedside drawers from IKEA a while ago, stained and painted, and replaced the knobs. I thought I’d go ahead and see what these would look like if I replaced the black knobs with Leather Handles.

DrawerDIYOriginalBEFOREAFTER01jpg

Here’s a quick how-to of what I did.

First you’ll need the following:

Tools:
Straight Edge (Longer than 13”)
Knife or Box Cutter
Hole Punch
(optional) Leather Strap Cutter
(optional) Cutting Mat
Tools01jpg
I’ve had this metal T-Square for some time. I purchased it at an art store way back when I was studying art in college. The box cutter can be acquired at any hardware store. The Cutting Mat is made by Fiskars and was purchased at JoAnn. I have the extra large size. I like mine to fill as much of my work area as possible. I’ve had 2 others previous to this. I would estimate that with heavy use its lifespan is about 1-2 years. The punch and strap cutter was purchased at Tandy Leather Supply. I’ve had both of these for several years and they both tend to work pretty well. For extremely heavy weight leather, or if the punch seems to get dull, you can try having another scrap piece of material underneath the piece that your punching so that you get a clean cut hole.

Materials:
Veg Tan Leather (at least 5oz)

Straps01jpg

You can go with a heavier weight leather. Just keep in mind that your length may vary. The piece on the far left is a template I created. Once I measured everything to my needs I usually like to have a master template to work from. This helps to eliminate having to measure certain details, like where holes should be, several times.
I’m not certain where exactly I purchased this leather. But, if you’re in Los Angeles I would suggest taking a trip to Sav-Mor Leather Supply and digging through their scraps. You may get lucky and find enough leather material that would work for this project. Tandy Leather may also have some material small and large enough. Other places you can contact are Weaver or Acadia.

Instructions
The first step you’ll want to do is to cut strips of leather at about 1” width. For these particular drawers the length of the strips should be at about 13.5”. If you have a leather strap cutter, set the cutter to 1” width. This tool will make it much easier to do, but it isn’t necessary. You’ll get by fine if you have a long enough ruler with a metal edge. If you’re not using a strap cutter make sure that you make your cuts on a cutting mat or some surface that you’re ok with cutting on.
Next, measure about an inch from each end of the strips and make a mark. This will be your guide for where you’ll be punching a hole. If you don’t have a punch, you can try cutting a small + large enough for your screw/bolt to fit through and trim if necessary.
At this point you’re pretty much done with the leather working process. Now all you’ll need to do is use your screws/bolts to attach to the drawers.

Some other things you could do:
With veg tan leather it’s quite common to dye or stain the leather. On another project for drawer pull handles I had stained the leather a tan color. You can purchase these dyes or stains at any of the above mentioned leather supply retailers.
You can also use a different screw or bolt to give the furniture a more modern and appealing look and feel. On the same previously mentioned drawer project we purchased brass colored spray paint and painted hex bolts (both purchased at a hardware store). The bolts were a little bit wider than the original screw holes so we had to drill the holes a tad bit wider.
Here’s an old picture of the example.BabyDrawerPulls01jpg

Thanks so much for taking the time to check this out. I hope this was and enjoyable and helpful read. If you have any questions please feel free to contact me. Have a great time!

http://www.MontroseLeatherWorks.com
http://www.instagram.com/MontroseLeatherWorks
https://www.etsy.com/shop/MontroseLeatherWorks
montroseleatherworks@gmail.com

We’ve Moved

SmallKeySkyBlueBackHey kids! It’s been some time… some miles… and a small addition to our family. But, we’re still hangin’ around and we’ll be reopening our online Etsy Shop. We’re no longer based in LosAngeles, California. We’ve settled down in Nashville, Tennessee. We’re still slowly settling in but will keep everyone posted with further details as often as possible. And although the location may have changed a little, our commitment to you remains. Thanks so much for your continued support. It means everything to us.
Handcrafted… NOW in Nashville, Tennessee.

www.MontroseLeatherWorks.com
www.instagram.com/MontroseLeatherWorks

As I write this letter…

This past summer we’ve been really super busy. Filling orders. Planning for wedding. Scheduling temporary shop closure. And a Special Summer Guest…

-1

We had the honor and pleasure of having little Ellie stay with us. She was rescued by an organization called Bichon Fur Kids. We offered to be her foster family until she was placed in a forever home. Bailey had a blast having a little foster sister for a while.

-2 -3 -4

Last night a new chapter in her life began. Her new forever family came by to pick her up. She’ll be living in San Luis Obispo with a great new Mommy and Daddy and older Bichon Brother. I know she’s gonna have the best time ever. We’re so happy that she’s got a new home and family that’ll love her forever.

We’ll miss you, Ellie! XOXO

 

If you’re interested in helping out Bichon Fur Kids you can check out the these links:

http://www.bichonfurkids.org/Available+Dogs
http://www.bichonfurkids.org/

Hooked on You – Keep Your Keys

Ever lose your keys? YEAH!… me too.

The worst was that time when I was on one of those rides at a fair that spins you upside-down. My keys just about literally decided to jump out of my pocket. Worst. The ride attendant was kind enough to help me get them from underneath.

midway

But, yeah. Totally annoying.

So, when I first started out I wanted to fix this issue. And, from there came the Long Key Leash. This was the first Lanyard design. It was great. But, I soon realized that there are a lot of other people out there who’d prefer something a little bit sleeker. Maybe something that’s even simpler. And then… THE MINI KEY LANYARD.

MLWMiniKey

This little dude has been great. Great for both Men and Women; Clip it to your pants belt loop. Or, onto your bag or purse! I’ve gotten a few custom orders that are a slight variation of the mini. And, even had one with an initial monogrammed on it. I’m also getting more orders for these from local shops like L.A. County Store.

I still get a few orders for the Long Key Leash. And, I still have the very first one that I made for myself. But, more recently I’ve been sporting my Mini. Since these pieces I haven’t lost my keys!… and I can get back on those RIDES!!!

Unique Goods

Los Angeles is home to some of the most creative people and is a hotspot for local businesses. UniqueLA Spring Show staged in Downtown Los Angeles during the first weekend of May. It was great time to shop for Mom right before Mothers’ Day weekend. Here are a few I went to check out:

Standard Wax:
Based out of Arizona, Standard Wax is a brand owned and managed by a creative duo.
Standard Wax

RicherPoorer:
Sock brand based out of Orange County, CA and manufactured in Highpoint, NC.
RicherPoorer Socks

PF Candle:
Based out of Los Angeles, CA.
PFCandle

Concrete Geometric:
Hand crafted Geometricly shaped concrete planters and other cool products. And, since it was May 4th I thought this appropriate:
ConcreteVader